Today I have installed my new Netgear router, and to be more specific it is the DG834PN model from the Wireless Rangemax series.
It is a great product, with excellent Wi-Fi support, a comprehensive settings menu and a cool design.
However I had the following annoying problem.
I didn’t complete the setup wizard, I went on and set all settings manually, even before the ADSL connection has been activated.
Thus, when the ADSL became alive, I got normally connected to the Internet.
And at that time I have been locked out of the router’s admin/settings home page.
Whenever I was typing http://192.168.0.1/ on the browser (Firefox 2.0 or IE7), the page was redirecting to http://www.routerlogin.com which is a domain owned by Netgear.
The solution that was suggested by the Netgear’s support page, was to reset the router to the factory settings.
Anyway I didn’t do that, because I would lose my settings, and the problem could be repeated as well.
So how did i fix the problem?
I opened the XP hosts file, and did a manual insert there.
The hosts file is located at: C:\WINDOWS\system32\drivers\etc
The entry was: 192.168.0.1 http://www.routerlogin.net
You might need to flush your DNS records at this point, or simply restart your computer.
And then use the following URL to access the admin page:
http://www.routerlogin.net/setup.cgi?next_file=start.htm
All done!
Edit (01/05/07):
Here is another solution to the problem, which is a fairly straight-forward way to disable the annoying wizard.
Type in your browser:
http://www.routerlogin.com/CA_HiddenPage.htm
Select: Disable Configuration Assistant, and click on Apply.
You can re-enable it by navigating to http://192.168.0.1/CA_HiddenPage.htm (where 192.168.0.1 is your router’s IP address)
i wanted to configure the wireless router.
can’t find pass word
How did you find your password or have you?
I bought a DG834N last week. Great router, havn’t had 1 single drop-out yet. Good bandwidth, etc, etc….
Everything would be perfect except for http://www.routerlogin.com!!! I ended up using the same fix as you, but I am still wondering what possessed netgear to take this very questionable design decision. Why even redirect 192.168.0.1 to a domain name??? What’s wrong with leaving it as an IP address?
Anyway, once you know how, the fix is very simple. So rant over, and good work blogging this.
I am still having problems with NetGear. I’ve been to all of the websites and ips listed above. The ip address and others I’ve found, go to nothing. And the website sends me in circles. Any new thoughts on this?!?! I am in desperate need of accessing my wireless and securing it!We moved to a new neighborhood and all of our leech neighbors are sucking my bandwidth. Thank you!
reset to factory settings and reconfigure it with security…
can’t figure this out. Have set up router, can’t connect to it with laptop. Have internet access, obviously, on desktop. One of the many diagnostics or set up wizards has told me two things I don’t know how to resolve.
Wireless service disabled, don’t know how to fix that.
configuration mismatch, don’t know how to resolve that. Am way beyond my understanding of this, am tired, been trying to resolve it for 2 weeks. Can anyone help? Windows XP on desktop, vista on laptop.
try going to the start menu and then search and type cmd and hit enter this will give u a black box then type ipconfig this will give u the ip address
Good info. Allowed me to access my Router.
I have a desktop and a laptop currently using a Netgear Router. Today I’ve attempted to link another laptop to the internet without success. The connection is requesting a “security key” or “password” and nothing I use seems to work. Any suggestions? Thank you.
having the same problem here,,,did you get the help that you needed?
Bruce if you are trying to set up a Wi-Fi connection, you should password-protect it. From your router’s configuration page, choose the Wi-Fi encryption method, e.g. WPA-PSK, and set your own private key. Then on the laptop, set up the Wi-Fi connection properties with the same values. Try to re-write the password on the laptop as well.
thank you decoding for your post i was thinking about getting a book “computer for dummy’s” but with all the help i can find in these forums why bother, i did what ya said took only a minute and i can now access my wireless safely
Please help me get connected so that I might be able to use my laptop other places in the house.
Can anyone help me! I’m really confused.
I bought a netgear router and it worked well for about three months. A couple of weeks ago my kids messed with my laptop and I had to use the restore disk in order for it to work again. I was able to restore my computer but have not been able to get my laptop to work wirelessly since then. When I called someone from netgear they told me that they thought that my internal wireless card “vanished”??? I really am not computer savvy at all and can not understand how this is possible. I bought the laptop with an internal wireless card (802.11a/b/g) and cannot understand where it went and why it would “disappear” . If ANYONE can assist me I would greatly appreciate it!!
i’m having the same problem exactly. My laptop says that the card is working properly but there’s no way to connect it to the, less call it, “router”…
Can anyone help-;
I run Mac computers on OSX, I have a Netgear modem/router which I had problems configuring the wireless security.
I finally managed this with help from the Netgear help line. I have two problems-;
1. My Windows laptop will connect without any problem, my apple laptop recognises the router but I cannot log on using the wireless connection when I type in my password it rejects it.
2. Two of my Macs will not connect to the router even though I did not change the set up. A further Mac and a windows pc connected right off. (All four machines have wired connections)
Thanks in advance to any help I receive.
CT
please help me,
get connected my netgear{wgt624v3}fireware router
i am realy confused,
during first set up router,until activat step i am put the wrong user and password, the it disconected
then i opened 192.168.1.1 they asked for user and password
i put admin and password and all my user and pasword but i can sing in the web , it show error code 401 unautorized
my mac is00146cdb99e
pk
Thank-you im so happy i could kiss u… well not really.
i would like to know how to change my wireless network name and password.
just go into the router settings http://www.routerlogin.net if you have netgear
Log into your router’s home page. The default address should be http://192.168.0.1 . And then go to “Wireless Settings” in order to change your Wi-Fi name and password.
Yeah good luck with that, you live in wonderland mate…
NETGEAR model WGR614NA
I have the same issue – I have done what you have suggestion, but I cannot get the URL to respond to the changes to the passwords in IE6, FireFpx 2, and NetScape 9. I would appreciate your help.
Bev
roterlogin.net is also included with this scenario. I truly question the integrity of netgear why this is so. Really what do Domain names registered to netgear REALLY have to do with my LAN. My personal firewall logs has the communication between me comp and router listed has ‘routerlogin.net’ this was after the lates firmware update…before it was just listed as 192.168.1.1. Gee…my lan was listed as trusted in my firewall (netbios, file shareing…ect. as a result in this change, Now roterlogin.net is listed as trusted and in reality it is reallt OUTSIDE my LAN.
Is it another way to monitor clickstream, collect data and insert their own ads? TO SPY… Peronally I do not like this and it raises some extreme privacy and security alarms in my book
spelling error….routerlogin.net not roterlogin
lates=latest
i have that router its not that big of a deal just reset it. it take all of 5 minutes to reconfigure just use static ip everything sets itself
Can any one help me i wanted to configure the wireless router. i wanted to information about all series router..
I would like to find my WEP No so I cn use my mobile phone with my netgear equipment
I am using a netgear DG834G v3 Router with windows Vista through AOL. I play links 2003 golf game online. I can join games but can not host a game due to the fact I can not find my IP address. Please help me.
Ian log into your router’s configuration page, and check the “Router Status” to find your IP address.
Also you may have to do some port forwarding for your golf game.
I really appreciate the help but I am not very wised up on computers. If possible could you explain how I do this regarding the routers configuration page etc, thankyou.
Ian open your web browser, and go to http://192.168.0.1/ , there you can find the “Router Status” page. The default username/password should be on the manual, or on the bottom of the router. If you are being redirected to routerlogin.com/net, follow the above article’s last instruction.
I have tried to get my router WGR614v6 to work with my lap top and it wont recognise admin or 1234 or password and it wont let me go any further. What do I do? I can’t believe this router can give so much problems.
need to know when i go on the internet the router keeps asking me for a user name and a password can you help me!
Netgear doesn’t run http://www.routerlogin.com…Your router serves that page to all computers connected to it. To change your settings on a Netgear router, just go to http://www.routerlogin.com, not 192.168.1.1 or 192.168.0.1. The routerlogin page will only work behind your router, as your router serves this page.
Setup my Netgear router a couple of months ago but now I can’t get into the setup page. My network is a 10.0.0.x network with the router at .1. When I run ipconfig the gateway is as expected at 10.0.0.1, but when I try to access the router with that address or the routerlogin.com address, it doesn’t find the router. I can probably reset and start over, but I’d rather not do that. Anybody got any ideas?
Drivel
i recently bought a netgear WGT624, when logging into the network from my laptop it asks for user name, password, and domain.. what are these? i didnt use a user name or anything when setting up…
Hi.
Every time I try the above suggestions I am directed not to my configuration page, but to the netgearlogin wizard page. It won’t recognise the ip config address in the url either. How can I get onto the ip config page so I can change my settings so I can access wireless on the laptop around the house and online gaming on PS3. I have tried the suggestions mentioned previously with no luck. Any help appreciated!
The router original IP address is not 192.168.0.1 like some of you have said. It is 192.168.1.1 unless you have changed it. You can also ping that IP address when you connect it. So, to configure it just type in your browser http://192.168.1.1/basicsetting.htm
If you can’t access the router then change IP address of your LAN to belong to the same scope like 192.168.1.15 and then type again in your browser http://192.168.1.1/basicsetting.htm and configure it.
My computer tells me that my ip address is 82.39.121.121. When I type this or anyother ip address into the browser it simply does not load any page and just times out. How do I overcome this to configure the router?
It is not the firewall stopping it either cos i’ve tried turning that off.
i entered my ip address and gateway into my xbox 360 to play online and it keeps telling me my gateway is wrong if anyone knows wats wrong pls tell me and does anyone know how i can get my wep key if so pls email me at jasonishard@hotmail.com
Here’s a tip, First purchase flash drive(USB), then get on Ebay to purchase a RJ65 to USB adapter, this is the only place I could find one. Now you have to use windows wireless network set up wizzard, It’s in the control panel via your settings. click on it and follow the set up directions useing the adapter and flash drive to plug into the router so you can obtain it’s parameters to set up all your wireless components., All I can say is it works for me, And best of all It’s simple…… By the way the adapters are only available on Ebay from Honkong, It takes about 10 days to get here, Also they cost very little, Usually come 4 in a pkg, for about $5 plus shipping…..
Hi, My mistake on my tip, It’s a RJ45 to usb adapter, Sorry, Clay…
Why is my name and Email stuck on the leave a reply?
Because of WordPress cookies. Clear them out from your browser if you wish so.
I am using the Netgear WGR614 v6 router upstairs connecting 2 PCs to my Linksys main router downstairs. When I enter 192.168.1.1 I get the Linksys router (which I know well ). What I cannot work out is the URL to open the Netgear router admin pages. It works just fine but I want to enable wireless and set up MAC address securities.
I have tried 192.168.0.1
http://192.168.1.1/basicsetting.htm
http://www.routerlogin.com
http://www.routerlogin.net/setup.cgi?next_file=start.htm
http://192.168.0.1/CA_HiddenPage.htm
http://192.168.1.1/CA_HiddenPage.htm (opens the Linksys router)
My XP Hosts file reads 127.0.0.1 localhost (I am running Popfile)
“CalcProgrammer1 said:
Netgear doesn’t run http://www.routerlogin.com…Your router serves that page to all computers connected to it. To change your settings on a Netgear router, just go to http://www.routerlogin.com, not 192.168.1.1 or 192.168.0.1. The routerlogin page will only work behind your router, as your router serves this page.”
If that means I will find acces to my router there, I don’t.
Is there some way of interrogating the NG Router to find it’s Admin IP?
it’s very slow or no correction for the downloding.
pls solve it for me.
HELP!!
I need help setting my ps3 up wireless it keeps saying LAN number wrong, were am i goin wrong, thanks
I just recently purchased a HP computer with a wirless network card. I have a PC that is successfully connected to a Netgear DG834GT/GTB 108Mbps ADSL firewall router.
My problem is that I cannott establish a wireless internet connection after trying all diagnostic solutions etc.
Can some one please help?
My new notebook is running Vista Home Premium & the PC is running XP professional.
Sir, can you help, I am trying to install Netgear DG834G. When trying to enter username & password in router login it refuses to except my registration username and password. George
i dont remember my pasword and username in routerlogin.con.i can do?thank you
hi cant get into my netgear DG834G to look at settings can you help please.reards alan
Hi I Use To Have Netgear Router InStill But I Uninstill It Because I Lost My Internet Now I Got It Back And I Try To Reinstill Net Gear Router And It Ask Me For The Name And Password And I Forgot My Old One But In The Instill InFo ItSay To Put In admin And Password For It And It Still Wont Let Me In To The Setting Please Help Me
Hi I am having problems connecting to my netgear please help
thanks
eleonore
Hi everyone,
I just purchased a netgear wireless router (MR814v2)
from ebay. And I’m having trouble connecting to the internet with the router. I have a desktop that runs under windows xp and a laptop that runs windows vista. I have the router connected to the desktop and trying to recieve a wireless connection for my laptop. I have followed many trouble shooting steps and even reset it to get the router to work for both or any of my computers, but have no success. I also cannot log on to the 192.168.0.1 website to configure the settings. I even looked into bridged mode to get it to work because I have a speedstream 5100 modem, but cannot refigure out how to bridge. Can anyone help?
Thank you,
Luis
Hi All
This may help anyone who’s tried all other solutions and failed. I ran a wireless network at home for years and found it very difficult – endless problems with slow connections and PCs vanishing off the network for no obvious reason.
Last year I switched to powerline networking (network through power sockets) and it’s been fantastic – very fast, very simple and very secure. If all else fails, try a product like those from Devolo (I use the dlan highspeed) – you just plug one into the router and one into your PC and that’s it. They just work.
And before anyone asks I don’t work for them! I’m a humble web designer by trade …
Mike
I recently went on to iinet naked DSl with the computer Windows 2000 and the phone plugged into the netgear router. The internet is fine but we have had so much trouble with the phone cutting out after ten minutes!! This can be so emarrassing as I am secretary of a Seniors group and do need the phone to be working properly. Can you help?
I’ve tried typing in the http address to get to my router admin, but get a 404 page each time. I have seen the admin page before when I created a secure environment. Both of the desktops are working fine plus the wireless for the laptop is fine, but I just can’t see the admin page.
Any advice would be really welcome.
Thanks.
I have a net gear router i want to lock my wifi with a code how do i do it im very NEW to this.
@rphatboy1: You ‘ll have to login into the router’s configuration page, and then set the password on the “Wireless Settings” section.
i have netgear router in optus package broadband.
i want to setup it as wireless, at present it has a ethernet yellow cable attached to it.
how to get rid of that yellow cable.
How do I change my channels on my router?
Hey, last year my family bought a router and i cant connect to it with my school laptop, so i always have to do my homework with my laptop in the living room. I would like to be able to do it in my room but i cant seem to get my laptop to connect to it.
I think im having a problem getting it up… like the little password screen and stuff…
hey homies can u access 192.168.0.1 with other ip adress
or in other computer to reset the settings
omg i went to 192.169.0.1
cant log in… wtas the user and pass?????
The 198.168.0.1 problem may be because this is MINE. I just happened to use my routing (?) number and I have come up with a bunch of people trying to connect to my number. Is there a reason for this? Or is it simply because they started with an erroneous number?
A lot of people seem very confused about how to access their router’s settings. 😦
To get access to your router’s settings, you need to know the default gateway address it uses when accessing the internet. (E.g. the 198.168.0.1 Steve mentions above.) Typing this into a webbrowser will load up your router’s settings in the form of webpage so that you can access them. (NB this is only available to the computer(s) you have attached to the router. You’re NOT accessing any website on the internet.
If you’re using WinXP, to find out the IP address your router uses do the following:
1. go to
2. type “cmd” (without the italics) in the ‘open’ box which appears.
3. This will open a Dos window on your pc. At the command prompt in this window type “ipconfig” (again, without the italics).
4. Once you’ve done this, look for the line of info that says ‘Default Gateway’. This is the address of your router that you’ll need to put into your webbrowser.
You’ll undoubtably be asked for a user name and a password. If your ISP provided you with the router, contact them for this (it’s usually set to a default). If you bought the router yourself, it should be in the documentation.
Hope this helps and sorry for the longwinded instruction.
>>1. go to blank blank
Doh, step 1 should read –
1. go to “start” and select “run”
…
Mr. Cardinal
Thank you very much for this information. Sorry for the delay, and thanks for the “Go To’, LOL I was thinking I was supposed to know where to “Go to”
I was trying my, or so I thought it was mine, number because I was having nothing but problems getting my connection to the Internet. QWEST had me do that one other time so I was trying to repeat the connection instructions. Is my router going to be QWEST’s router and then my “address” is only through their router? Sorry, ask me about race car setups but, not computer issues. LOL, it’s lucky that I know how to spell Internet is much less do anything with it sometimes!
Thanks again
Steve
Hey thanks your fix worked!
I have a website that I believe my ex-BF blocked through the router for me. When I try to do the computer IP address, or the routerlogin.com, I get the same error message as the blocked website. When I try to go to the gateway IP, a user ID and password is requested. Do I need to call NetGear to get the user ID and password that he probably set up? I’m finding all kinds of things I think he may have done. I have been working on blocking all portals tonight, and I would like to be able to see which websites he blocked through the router. Thanks,
i forgot my name and password, i want to change it, how i can do? my ip is 192,168.0.3
jus do a hard reset 2 da router….
i forgot my name and password, i want to change it, how i can do? my ip is 192,168.0.1 please send with my email
I’m setting up my Netgear router, and I’ve opted for secure setup. Its asking me for username and password. It seems to be rejecting any username password combination I enter. Can somebody please help me.
i have some how lost my connection to the intre net on my lap top. i am using Netgear….DG834G . THE CONNECTION WENT ALL OF A SUDDEN WHILST BOOTING UP -AS I NORMALLY DO!- I DONT REMEMBER CHANGING ANY THING??.allthough every thing says fine my addapter is not found by the laptop…i connect wirlessly from my desk top .iam running vista and i keep getting the message that MEDIA IS VANNISHED …PLEASE HELP . DOES THIS MAKE SENSE? THANKS.
I have netgear wireless router and i hope that i can look fast and everyweb site
I have a computer and I don’t know what the frick I’m doing.
Send me an email to make it work.
Thanks in advance.
You morons are hilarious.
i want you to help me t, bout how to make a password in using neatgear wireless router, coz i dont want any body to use my network, thank you.
I’m trying to access my router’s settings, but I am unable to connect using the routing IP address in the browser, i don’t know what to do. I can’t connect to my wireless connection, only I have a local connection only instead of a local and internet connection. I dont know what to do the default IP addresss, 192.168.0.1 doesnt work and everything else sends me to the netgear home page. I don’t know what to do, its been a week, PLEASE HELP
i have netgear router and i would like to surf the net with super fast speed, i’m using a 1mb speed from my ISP and i want to download files with speed 20mb hehehe, can i do that you newb’s ?
If you tried all suggestions how to get into your router and you still can’t, that is what the “reset button” is for. It will wipe out all information stored, so make sure you have the disk that came with the product. Make note of your ip address and other settings first. The reset button is located on the back of the unit or on the bottom. Use a pen or a paper clip and push it in for a couple of seconds and release. Let it boot back up, then you are starting from scratch with the user name “admin” and the password “password. Run the wizard on the disk, and write down your password!!! I personally slap a label on the bottom of the router so I won’t forget!
what happens when you can not locate the disk??? Ive been gone for a while and can not find it??? the password was never changed, but the routerlogin.net does not allow the password. Any Idea, I need to install a password, also I seem to have registered under another email, probaly one of those netscape or Juno which I had some times.
i’ve tried your method and nothing has worked for me… can someone please help me i tried all the 192.168.1.1 and 192.168.0.1 nothing seems to be working. i did a hard reset and its still not wrking. the page loads up once i type in admin / password but nothing else seems to happen just loading. in IE ex and firefox. this is getting annoying. all i want to do it secure my wireless asd set a password. please help
Kunal,
if you have the disk that came with the product, just boot up the router first (after you reset it), put in the disk and do the wizard. It will ask all the right questions and be prepared to put in the information about your internet provider, dsl or cable, but most of the time the wizard does all of the work! If you live in the US and you have AT@T Yahoo DSL service, your ip address might start with 10.xxx.xxx.xxx. You can look that up by going to (in Windows XP) start,run, type “cmd”, press enter. Type ipconfig /all There is a space before the /key….If you still can’t connect……sorry, I am out of ideas!
In order to change your router name and or password for Netgear model WGR614 v7, go to http://192.168.1.1. It will ask you for a user name and password. The default is “admin” and “password”, but I was asked to change the password upon initial setup. Once you are connected, go to Wireless Settings and you have the option to change there. Hope this helps.
Thanks for this informative post – I have been trying to set up a wireless WEP for my friend but could not get to his admin page. Im sure theres a very simple way of manually doing this (?) but I have not tried before and just wanted the configuration page back.
I am also wanting to get to the page where i can set up my wireless router. I have never done this and was wanting some info on how to.
Was just looking over the comments here trying to find an answer to a question I had, but no dice. People on here seem to have a lot of trouble logging into netgear routers though. For all in question, it is routerlogin.NET (not com) in your web browser. OR if you want to know the actual IP address instead of just typing routerlogin.net in your browser, you can go to start, run, type cmd, enter, then ipconfig and enter. (This might list more than one network cards information, you’ll have to recognize the name of yours) The number next to “default gateway” is your router address, which you can type into a browser to get to the same routerlogin.net page. It will most likely be 192.168.x.x unless you changed it. It can be changed to whatever you want it to be. The question I had was whether there is a way to change the logon name from “admin”, instead of just the password. Doesn’t seem possible. All I can find anywhere is a field to change password, nothing about username 😦
Can anyone help me hook up a ps3 on the net for my son. I bought a netgear router and its asking for a wpa key, and I went to the page that was supposed to give me this key and ended up 192.168.0.1, and I just don’t understand what it is I am trying to do here. Thanks
test nor work
This 1 is 4 Tonywarner….
hi there,
Now it depens on ur ps3…whick key does it supports….but u can launch IE n type in 192.168.0.01 press enter it vll ask 4 da username n da password jus Admin n Password ull get da router page
on da left hand side plz click on Wireless settings n then it vll ask u 4 ur wireless name type in ur name n change da channel to 11 then come 2 da bottom of this page ull c security encryption with 3 options
Disabled,Wepkey n Wpa key select Wpa n it vll ask 4 da password
jus type in da password of ur own choice but make sue its alphanumeric n jus click on apply…ur router is confiqured 4 wireless n then u can confiqure ur PS3.hope it wrks 4 u
the ip add is wrong ova here….sorry 4 da mistake guyz
its 192.168.0.1
the above comment can also ty n zoe s well
Hi,
Iam Patel here.
I have purchaged NETGEAR RangeMax Wireless-N Gigabit Router WNR 3500 Serial Number : 1SP6927A00A65 and install today in my Home Hp Computer System : Windows xp 32 Bit but in my Hp pavalian d7 Laptop it not support and not working internet in my Laptop. My Laptop System is : Windows Vista 64 Bit with 320 GB Harddisk. Laptop asking always Security key or Passpharse still Iam confuse and not able to start internet in my Laptop. kindly give me proper advise and instruction for above problem.
Thanks for kind co-operation,
Babulal Patel
Hi again
this 1z for Babulal Patel
ok its askin 4 da passphrase tht means its askin 4 da security key which u need 2 confiqure by acessin da router page 1ce ur in da router page plz follow da above comment which i’ve posted on May 22nd, 2009.
lemme know whether it wrks 4 u or not…
thanks and regards,
Vish
i need to change my settings on my netgear WGT624v4 but it’s been a year since i last logged in and i have changed laptops..and i don’t remember my username and password..how can i change it/update it and how can i sign in to do this??
thanks!!
i need to change my settings on my netgear WGT624v4 but it’s been a year since i last logged in and i have changed laptops..and i don’t remember my username and password..how can i change it/update it and how can i sign in to do this?? i need to change some things asap.
thanks!!
hi there…
this 1z 4 chrism,
if u want 2 change da details on ur router…..u can do tht….jus turn da router upside down…ull get da username n da password….n also how 2 access da router page….jus go thru this n update ur router…..
Vish
Ok i have a tricky one. i just got a netgear WNR-2000. I have Contacted my ISP so they could change the MAC add. from my comp to the routers… everything is good on my desktop, i have connectivity. I set up Ip to recieve dynamically and my DNS obtained through ISP, TKIP and AES for security, SSID = BarWRranch, Channel = Default, and its running at 145 Mbps. I go to set up my laptop. Finds BarWRranch (5 bars- excellent) i type in my key and it connects. shortly after (approximately 1 min) it disconnects. Maybe interference… Boost it up to 300 Mbps and change my channel to 11 ( i live out in the country and just got a new fiber line finally! :P). No the problem persists. Firewalls turned off and also disabled my Kaspersky filter just to be sure…No. After some more research i have learned that every time it disconnects and reconnects it assigns a new ip in order of the range 192.168.1.3, 192.168.4, etc… and also that my IpV6 stays limited (not sure if that is relevant). I run Vista with an Atheros Ar5007EG wireless card. Any Ideas???
Hi Ladden
Jus a quick question…..have u tried changin da wireless name n da password….wat kinda security key is enabled….u can try changin tht s well….
thanks and regards,
Vish
Yes i have recently re-installed router with No Security and Default Id = Netgear… does not help. I am thinking that something is messed up with the modem or my ISP has something to do with this problem, however i cannot reset my modem because i have none i can access. When they set up the connection i believe that the modem is in my phone box…(this is the first fiber connection i have set up or seen for that matter) so i do not know if it is even possible to re-set it. I have also tried to update my drivers on my wireless card and they are up to date. I have also tried to save my network setting via security pin (Not sure if this is for a computer, maybe for x-box etc..) and came up on this message “Configure a WCN Device” Windows cannot save your network to the selected device. This program is blocked by group policy.
Any help on this matter or new ideas is greatly appreciated.
Thanks]
Ladden
PLEASE CAN SOMEONE HELP ME BEFORE I LOSE MY SANITY!
In April I purchased a HP Pavilion Slimline Desktop and set it up with my exisiting Netgear DG834G router. All was well for three weeks. Then I found it virtually impossible to use internet and windows mail 7 when wired connection – but wired worked OK.
My other compac laptop has worked fine throughout. This insists Netgear demonstrates that there is nothing wrong with the router.
The vendors support line has not been able to rectify it – technicians came out and replaced the motherboard and this did not worked and tried everything they could think of and nothing has worked. I the end I exchanged the machine for the new HP Pavilion Slimline s3811UK. As soon as I set it up today, exactly the same problem. No internet or email conenction, or at best the occasional very slow conenction – this is wired – when its wireless it works fine!
Its still at its factory settings, no software loaded – please help me someone …
Hi Stephen,
Do da hard reset of da router…..n confiqure it manually…make sure da VPI,VCI n MTU size r st correctly….same thin happen wid me s well,did da manual confiquration n its wrkin f9…..No slowness s well lemme know whether it works 4 u
thanks and regards,
Vish
i recently bought a netgear router and i have connected to the internet okay on my laptop but i cannot pick up a wireless signal on my home computer any suggestions?thanks
You do have a wireless card installed on your home computer, right? Otherwise you will not be able to connect to it wirelessly.
In my case, Netgear router – 192.168.1.1 redirects to http://www.routerlogin.com/welcome.htm – how to fix it ???
Hallo Blog Administrator,
Greetings to you and all the forum members.
After having googled and researched in the Internet for the last 7 days on, I finally came across this very informative blog or forum site, where I can see at the top and read the similar case mentioned and described.
I simply cannot log in the configuration page of the router for a further setting.
NETGEAR Support has suggested me to bring the Router to the original factory settings by pushing the reset hole, which I did.
I have a wireless NETGEAR Router WGR614 v6, which I bought 3 three years ago. At that time I wanted to create a wireless home network in the house, connecting my desktop computer and another one in the basement. I still remember I had spent such many day and had to take pains to set up my router but in vain.
Now after three years, I find myself trying very hard to set up the same Router again, because the family members want to have their notebooks connected wirelessly to the Internet through the Router to be connected to the Modem.
My great concern right now is this. How can I come to the setting page of the Router?
They say that I should enter 192.168.1.1 (which is by the way my Router’s gateway address) on my Internet Explorer browser (I tried it also on Firefox or Opera!), then there must, they say and insist, come up a popup where I will be asked to type both username and password so as to come to the Router setting page.
The fact is, I never encountered this popup, therefore never landed to the Router setting page. The fact which makes my nerves irritate.
In my case, Netgear Router – 192.168.1.1 redirects to http://www.routerlogin.com/welcome.htm .
Support suggested to me that I should type http://www.routerlogin.net , but this too redirects immediately , without exception, to http://www.routerlogin.com/welcome.htm .
The Welcome page tries to tell me to go along with how to cable the Router to the PC and eventually to the Modem, the procedure of which I do not want to do for the moment.
Rather, I desperately want to set up the Router first, and then proceed to how to connect to the Internet.
So the question is – how to fix my problem.
Now, I would like to try the Forum Administrator`s roundabout solution.
I sincerely hope that it will fix my problem. I want to finish with this tiresome monkey play.
hey hi hiro,
As i can c ur facin lot of probs bcoz of ur router…
n its says tht wheneva u type da Ip add it gives u da welcome.htm which is of no use. but if u can temme have u tried resettin web settings n if u can check da Ip address by typin CMD in da run command box n then Ipconfig in da black box. The correct add should 192.168.1.2,3 or 4.
You can also try n typein routerlogin.com…..it works most of da time
Lemme know if its works 4 u
thanks and regards,
Vish
hi there all Great Feeds here, thanks for all the input!!!
I have a Net Gear Model WPN824 v2, both computers runs window vista premium, 1 hooked up via ethernet other is wireless, I am getting ready to hook it back up after I moved, over a year ago, I know I have to reset the router since I don’t remember my name or password that is no biggy there, I know how to access to get my ip address, but I was informed that I need to set my DSL router which is a westell Model 6100G to bridge, that is what I am not sure of on how to do? any help would be greatly welcomed regarding this. also being that I am resetting my Net Gear Router should I take out the install from the last time I installed it or not worry about it Some things I know you have to take out in order to do a re-install.
Thank You in advance for all your help regardingthis matter!!
Have A Great Day!!!
Hi,
I am super disappointed about NETGEAR and
am shocked about the service. After selecting
my router, There was not service for hook-up unless I paid for it. It still insn’t working.
This is outragous and a ripe-off. Don’t trust
these people.
Pay for hooking up a product for the first time
isn’t what is suppose to happen.
Barbara Ingleside, Il Unsatisfied Best Buy
Barbara,
Can you describe you problems more fully? I have a netger wireless router and have never paid for any hook-up or service…
Glenn in IL
Hi thanks so much! I was so happy that the http://www.routerlogin.com worked I had to leave a comment! thanks again..
When i plug the cable directly to the computer , internet works properly , but when i connect the router , i will have limited connection , so maybe i should reboot the router , but the site (192.168.0.1) is not working while iam having limited connection . what should i do ?
how to reset the router ?
resseting the router is soo easy like picking apple in your backyard…….go to back panel of your router beside of wan connector with a small hole just insert a small pen into the hole and long press until 30 seconds……the disadvantage of ressiting is your old configuration of your router is probably disappear
What a crock of shit!
The url to change my netgear router settings
192.168.1.1 does NOT work and every time it will not allow me access. Unbelievably frustrating!
Yes securty is off and firewall is off yet no luck.
I guess I get to pay $29.00 to get this reset becuase logging into my router to reset the settings myself is proving a time wasting imposible task.
Bullshit
jus try http://www.routerlogin.net it works…
WOW!! I GOT THIS THING JUST MINUTES AGO,IT’S WORKS
GREAT AND IT WASN’T EXPENSIVE ALSO.
Well, four months on Erwin…i wonder where is your netgear router now….
I purchased my Netgear on July 2008 and connected it to a HP with vista I use AOL it worked fine until the forst part of August 2009 then I cannot connect to AOL dirrect I can get it through internet explorer,I contacted AOL they sugested the software was corrupted so I unstalled it and attempted to install a new version, I got the same Message that they could not find a connection. the computer that is connected to the cable direct has no problem, HELP. ED
Hi all,
Got a brand new WNDR3700 router that is set and working fine. BUT it is impossible to me to set a port redirection rule!
I’ve got two webservers behind the router (A and B) and I have to get the port 80 redirected to A:80 and 8081 sent to B:80.
Actually, I create a simple “forward” rule for 80 (http) directly to server A, but I just can’t find how to redirect 8081 onto my other server.
The panel proposes to set a trigger rule but I’m not sure how to deal with that (and whatever I tried, it did not work).
Could anyone help?
Regards,
Ann
I have got a netgear working but I need to put a security setting on it, can anyone help me out..I think someone is using my network
hi there,
Now u can launch IE n type in 192.168.0.1 press enter it vll ask 4 da username n da password jus type in Admin n Password ull get da router page
on da left hand side click on Wireless settings n then it vll ask u 4 ur wireless name type in ur name n change da channel to 11 then come 2 da bottom of this page ull c security encryption with 3 options
Disabled,Wepkey n Wpa key select Wpa n it vll ask 4 da password
jus type in da password of ur own choice but make sue its alphanumeric n jus click on apply…ur router is confiqured 4 wireless n then u can confiqure ur lappy.hope it wrks 4 u
its not working .i paid 125$ 4 this sheat.its not have. a reset batton.where is a batton to reset .i cant make him to work wirelless.
bojian catalin………
u find the resset button in da back of da router in da small hole
just ensert a hair pen or a ball pen in the circle hole and push it untul 30 msecond
make sure that if ressting the router the power of router is turning on ok
im from netgear tecnical suppurt
please help! im trying to set up another computer to my netgear wireless router but i cant remember the WPA key. i tried to access the router to find the WPA key but i can remember my user name or password either! is there any way around this?
I have a Netgear wireless router model # DG834G.
I have had trouble connecting to the internet. I contacted my service provider and then Netgear support. My provider would not help because I am using Netgear not their AT&T model.
Netgear support told me to call Apple because I am using a Mac table top computer and a MacBook laptop.
I finally got the lap top working but I am unable to get the wireless set up for the desktop. ie ( name,passwords).
I have read all of the questions and comments. I do understand about the reset button on the router but my question is if I hit the reset button will the settings on my laptop change and make it necessary to redo the laptop?
I don’t want to mess the laptop up.
I would appreciate any help that you can give.
Thanks
I bought a netgear wireless-g WGR614 v9 router from ebay, i dan get on the internet but can’t find my connection to get my wireless laptop on the internet. can anyone please help///can’t get past the admin, password in the netgearlogin page
the thing you have to type into ur address bar is 192.168.1.1 NOT 192.168.0.1
I having enough problems with it. I think Netgear is an embarrashment for the stater of California and i live in the uk. Thanks.
I must apologize for that comment as i made it after more than a month dealing with the nightmare of routers. I guess the state of California has got nothing to do with this company. One thing is for sure: i am not buying a netgear product ever.
It doesn’t matter what you do. AND WE BOUGHT THE SAME MODEL TWICE!!!!!!. DG834PN. I think it’s a disgrace, and i cannot believe that these people dare to call themselves professionals.
it will break the wireless card in your laptop (802.11a/b/g) like it’s happened to Liz H and myself. If you buy a new router make sure it’s not netgear.
i have a ipod touch and i also have netgear1 and for the WIFI to work it needs a password i dont know what the password is what is that?
PLEASE HELP
the username is admin the password is password
am uitat parola
no lo save los password
I am through with netgear I will buy never buy it again. I have had nothing but trouble. I am going back to linksy. I never had any problems setting them up.
I have read all of the questions and comments. I do understand about the reset button on the router but my question is if I hit the reset button will the settings on my laptop change and make it necessary to redo the laptop?
I don’t want to mess the laptop up.
I would appreciate any help that you can give.
Thankshair loss forum
How do I set up a Dynamic IP address for my wireless RangeMax Wireless-N Router? I do not know how to do this PLEASE Help!
Thank You
John
Dear Sirs
Can you help us in accessing some controllerof Rectifier system through GPRS modem with follwoing:
IP adress of controller: 192.168.0.1
IP adress of router GPRS modem: 212.212.164.91
REGARDS
Mobile:00965 99634 962
Pls help
My Dell windows xp is connected ta a netgear router, My note book isn’t connecting to the wireless router anymore. Cant’ get the notebook to work wireless. It comes up connected but that’s it. Help!!!
hello im trying to reset or change mynetwork security key played with it now i cant get on my lap top can anyone help me
I just bought a netgear wireless router with modem. everything is hooked up corretly (wires) all the lights are on except the internet one. My computer says it has limited or no connectivity. anyone know how i would go about getting this thing connected?
I’ve hooked my computer back up to the router the phone company gave me it works. I’m trying to get wireless for my xbox and ps3. Please help!
how do i reset the net gear router forgot password thanks !
Senhores,
na renstalação do reteador WGR614v9 aparece um pedido de usuário e senha. Coloquei a o usuário e a senha do provedor da internet. Nada. Coloquei possíveis senhas usadas em outros e-mail meu. Nada. Afinal que senha e usuário são esses que vocês estão pedido?
can you please help me with my connection on my laptop.
t is asking for a renew ip address it used to work but it stopped.
hi guys. got a few problems im hoping you can help me with.
first is like a number of others when i try and log in to my netgear router, my password (which i know is correct, its ok on my daughters laptop) is not being accepted. i guess i may have to reset settings, which is a pain and i hope it doeasnt happen again.
2nd, i have a wireless network/router, but cannot afford one of those mini wifi adapters for the back of my sons xbox 360. so instead i bought a long ethernet cable, which ive connected router to xbox. i cannot connect. my wireless name and password is coming up and ive tried using the manual setting ip address etc. but no joy. any ideas. thanks
I have a Netgear Rangemax Router (WPN 824v2) connected to a ADSL modem. All running well. Broadband contract.
My XP Home comp. is cable connected to the router, speed: 550.xx kbs (Nova Friburgo, RJ, Brazil)
My (2) HP laptops (Vista HP 32) connected via WiFi, speed: last few days: 55-150Kbs, normally 350Kbs.
When latops are cable connected directly to the modem, speed: same as XP comp.
Processor name: AMD Turion(tm) 64 X2 Mobile Technology TL-60
Processor speed: 1994
Processor vendor: AuthenticAMD
Processor count (cores): 2
Processor ID: x86 Family 15 Model 72 Stepping 2
RAM size: 1.94 GB
DirectX version: 4.09.00.0904
Video RAM: 64 MB
Windows version: Windows Vista (6.0.6002)
I have made these changes trying to increase the speed:
I did everything listed in Tips manually before applying the patch that reportedly did the same thing (did not see the patch at the bottom until I spent my time manually!)
http://www.speedguide.net/read_articles.php?id=2574
I also did what is suggested in this article for configuring my router to run faster with bit torrents.
http://p2p.weblogsinc.com/2005/04/24…ent-downloads/
Find the section that says*Port Range Forwarding*or similar
4) Add in the port range*6881-6889*for Torrent files
5) Make sure you check both protocol boxes*TCP*and*UDP*as well as the*Enablesetting.
6) Have the forward address set as your internal IP address*192.168.1.3*in my case.*
7) Turn on Port Triggering telling it to forward the ports you list above with the trigger port set to 6881 and the protocol to TCP.*
Any suggestions?
I realize I probably should tackle only 1 problem at a time and leave the torrents issue for later.
The ISP reports all is fine and will offer no help…Brazil sucks for Customer Support by the way.
Regards, Mark
http://forums.techguy.org/networking/923803-slow-internet-speed-router-vista.html
will i have a WGR614v7 for my xbox and it is saying i need a password to get on i never set one up
2 routers still not working know what my username and password is
thanks this helps!
un: admin
pw: password
I type in the 192.168.1.1 and it doesnt work, neither does 192.168.1.0 i havent changed the settings either so idk……
Hi guys,
I bought a Netgear WGR614 v6 from EBAY a few months back & am still struggling to get it sorted.
I am attempting to use the router as just a router for WiFi having been connected to ADSL via TPG with a speedtouch modem. I’ve tried using the Netgear modem as the only modem but when configuring it gets to the end page & then will not accept my ADSL password etc to connect to AAPT.
Now I’m happy enough using to devices but the issue is turning WiFi on.
Going off a previous comment I have got into Netgear’s settings via http://192.168.1.1/basicsetting.htm and all looks lovely.
I have set up an SSID & WPA password but on the Router Status page it lists
Wireless AP: OFF
Broadcast Name: OFF
I have then found the place that seems to turn the system on in regards to WiFi under “Advanced Wireless Settings” where i have the options to tick the boxes on
Enable Wireless Router Radio (not currently ticked)
Enable SSID Broadcast (currently ticked)
Now to me the idea would be that both of these boxes must be ticked & most importantly that first box, but the box is blanked & completly unable to be ticked.
Does anyone have any ideas for this or if I have to select something in a previous field to get this selectable?
I also remember a mate telling me to switch DCHP off but I’m unsure if that was related to WiFi so don’t want to touch.
Any help you could give me would be GREATLY appreciated.
after aquiring my old router from my old house i recently plugged it into my pc via ethernet, following what i know i tried to log into the settings by typing in the usual 192.168 etc in my explorer page, and nothing! ive tried everything and im at a loss, ive tried all the methods of setting it up routerlogin.com, 192.168.1.1 ipconfig soulutions in cmd didnt work either, is it the fact that i have a dsl modem installed on my pc? please help! its a DG834G model (wireless)
Why do you call this a problem? This is a feature of the routher. And the domain http://WWW.ROUTERLOGIN.COM will not goto the internet, it will be resolved to the router’s local IP.
This is for an easy way to access the router administration panel without having to type in the IP in your browser’s address bar.
The IP address 192.168.0.1 is the default for some home broadband routers and other types of network equipment
Hello,
I have a netgear route connected to my desk top and I can’t seem to share internet connection with my wireless lap top. Please help.
I also probably need help with set up
router box model WGR 614 V8
@Kola
I have the same router, you don’t need to share the internet connection through your laptop, you can share it through your router.
Connect the internet jack to the INTERNET port, and you are done, internet is already shared through your router.
Thank You for this, I really needed to get into the router cause the setup that it was doing was failing but it wouldnt let me into the settings of the router untill it was done, typing in http://www.routerlogin.com/CA_HiddenPage.htm was the moment that marked the beginning of the working of my new router.
Thanks for the info!
why is it i am not able to log thru the admin account using the default password as “password’ during the first time i set up my netgear wireless router WGR614 V6?
Thanks and more power…
how to get password
I have just bought a wifi printer from epson. It equires a password to key it in to your router.Could you please supply that password.
I have just remeembered that you might need the serial numberof my model DG834G v3 ;it is 1JX376BR044C7 needed to find the key I need to access my epson wifi printer.
It did not explain that clearly at all in its manual instructions
i also tried to access 192.168.0.1 (and all the others) with no luck..i finally stumbled upon my router’s IP, as cmd did not show it. Try 192.168.182.1
It worked for me
i am trying to find the control system settings but i cant find it? please help me i am so frustrated i really want to add my xbox 360 to wireless list.
how do you lock the wireless so nobody else can use it while you are because sombody is useing mine and we don`t know who is it
I bought a Wireless Cam and it works OK but if I send other People the link to see and watch my Cam the can’t get it its blocked but I use my Laptop I see it .
Quation how to I let that link go to my Netgear Route so that People I give the Link can see it .
Thank you Horst
i have forgotton my passwprd for my wireless router how can i change it can somebody help.
i have forgotten my password
i am unable to login into my router the verison is WNR2000v2
i have tried all the logins that i have managed to find but nothing seems to work.
please help asap
THIS IS ALL BULLSHIT. TOTAL BULLSHIT.
you got guys like vish sorry to be rude and many others stating the same shit over and over again
3 hours ago when I typed in http://www.routerlogin.net it took me to the router screen.
Now I type it in and it takes me to the gay netgear website. wtf?
Next I tried that 192 crap and same thing.
Then I went to cmd and typed in ipconfig
ip release
ip iprenew
I managed to get a the deafault gateway address
I typed this in and same thing again.
‘Ooosps that page can’t be found’
Nothing has changed. Only diff is before when I was logging in to the router login page my internet wasnt working, and now that it is it takes me to the netgear page.
And solution ??? The first post at the top of the page I think had my solution but the guy writes
c:/windows/system32/drivers/etc
WTf is etc mean ? if your helping someone find a specific file why are you writing etc at the end what an idiotic response.
In my case solution was: to remove proxy server from settings of my web browser. Website http://www.routerlogin.net is not present of its cache, so it redirects to Netgear website. Do not any changes in hosts file in folder c:/windows/system32/drivers/etc, in my case it was false way.
i had the same problem after fiddling with my router, i had accidentally put the lan wire from my modem into one of the numbered ports and got the same redirection problem you had when i put it in the correct port it all worked nicely
Type in
Username: admin
Password: password
It’s not that hard.
Could you please help me? I have a wgr614 router and put a password on it a couple of years ago and have lost it. Can you please advise me how to retrieve or change it.
Here’s what worked for me on a Windows 7 SP1 computer.
With the computer off, disconnect the ethernet cable to the network.
Connect a regular, straight ethernet cable FROM the computer TO the Netgear LAN Port 1 (NOT the WAN port and NOT a cross-over cable). Make sure this is the ONLY cable connected to an ethernet port.
Turn on the computer and make sure the Netgear router is on.
Go to the Network settings control panel. In Windows 7, its at CONTROL PANEL | NETWORK AND INTERNET | NETWORK AND SHARING CENTER.
What you want to do is make Windows forget it’s original settings. In the Windows 7 control panel, select CONNECT OR DISCONNECT, then SETUP A NEW CONNECTION OR NETWORK.
That opens a window with 4 choices. I picked SETUP AN NEW NETWORK – Configure a new router or access point.
Windows did it’s troubleshooting with the new network.
Once I got Windows to see the new network, I opened a browser window and typed in http://www.routerlogin.net (which is the address written on the router).
The Admin Login window with name and password prompts opened at that point.
When I first began this process, I typed in the URL’s as well, but those took me to Netgear’s internet page. Typing the 192.x.x.x addresses returned nothing useful, either. I realized that my current network was interfering with the Netgear router connection. Thus, make the computer forget the original network and make Windows see ONLY the Netgear router.
BTW, I also tried to connect the NETGEAR router to my original LAN router, that didn’t work, either.
I hope this helps someone get to the stupidly(!!) configured NETGEAR router admin pages.
WEP key for the password so I can know the WEP key
this is the worst product ever if your not computer savvy, I cant figure this netgear out and the program is stuck in my laptop and wont erase i was just so anixous to use this product in order to receive wireless services to use my kindle.. and furthermore once u buy netgear its really no help and you become confused cause dont know if you did something wrong this should be made a little more friender to people whos not techincan..
eu tenho um router NETGEAR e usei o link para configurar ele pede nome do Usuário e senha , jogo e diz invalido;
eu uso ele numa maquina e pretendo aumentar mas uma maquina para conectar so qdo faço isso e uma conecta outra nao consegue conectar .
sera que tem ai aguem que pode ajudar-me
Hi, I just bought this wireless router at a yard sale with everything in the box for 5 bucks, and it connected both our computers to internet, but when trying to direct me to the ip address it asks for a password and a username which doesnt seem to be admin and password. Someone before me must have changed it, help we want wireless too.. Idk why the internet connected both computers right away without the password.. How can I find the password and username out?
[…] [1] https://decoding.wordpress.com/2007/02/21/netgear-router-19216801-redirects-to-wwwrouterlogincom-how-… […]
If all else false push the reset on the Netgear box and start over. Again “admin” is the username and “password” is the password. You have no surcurity with your wireless network once you reset so I suggest you try to set it up again. There is Documentation on this in the router just read up on it.
After typing the http://www.routerlogin….. in browser, hit the ENTER key, NOT search.
Thanks for that IansG, Ive been tryn t sort problem for 2hrs an your sollution spot on:)
i would like to change my password so no one in the neighbourhood can connect to it.
Thanks
sam
i cannot connect to the router log in site it keeps redirecting me to the support site how can i bypass that? PLEASE HHHHEEELP!!!!!!!!!!!!!!!!! or do anyone know the passphrase to the wnr1000 netgear box so i can put it in my computer and then i can disconnect from this ether cable……….
have lots of questions ……no answers!!!!!!!!!!!!!!!!!!!!!!!!!!!
Hi, I’m trying to connect 2 routers together. After googling for a long time, I know a few things. I want to make the primary router as a parent, and the 2nd router as a child.
So having the primary router already set up, I linked it to the 2nd router at the Lan port with an ethernet cable. Then I linked the 2nd router with my computer to with ethernet cable.
Here I try to change the IP of the 2nd router (Netgear). My primary router’s IP is 192.168.2.1 to 192.168.2.94. So I want to set up the 2nd router’s IP to 192.168.2.254, and disable its DHCP.
At the LAN IP page, when I clicked apply, the page loads saying “updating.” But it always showed “timeout” then “server not found.”
I don’t know what I’m doing wrong here. Is it because I don’t have a crossover cable?
Please help, this is so frustrating to a newbie. Thanks.
Most of the NETGEAR devices, except ReadyNAS products and Fully Managed switches, have the following default username and password:
Username = admin
Password = password
For older devices, password = 1234
If you have changed the default password and have forgotten it, you will need to reset the NETGEAR device to factory default settings in order to use the default username and password. Click here to learn how to reset the NETGEAR device to factory default settings. Please note: restoring a device to its factory default settings will erase any changes you have saved to the device.
im new with computer have wireless but ilive in a dead beat apt and low lifes are hacking in i need to now how to put a security code in
I have a router ref no. DG834G v4 and have forgotten my password (Key) for me to connect to a TV .What can I do to retrieve it or substitute another
I install y netgear WND4000, everything worksfine n my desk top.
when I use my lap top elsewere, it connects perfectly to other wireless.
When I tried to use my lap top here at hme.. it does not connect. thru wireless.
I had to use my enternet cable to get to the internet.
How can I resolve this problem
Shahyed646@yahoo.com
sorry how do you set up your WGR614 router to you xbox and make the internet work ; mine dont seem to connect.
please let me know my password, user name should be pamela
Using the active voice helps when writing the narrative.
I’m having trouble with my netgear router. I’m unable to load routerlogin.net, routerlogin .com. I’m trying to hook a roku wireless device into my network and roku is unable to connect to my local network. Any suggestion?
try this:www.routerlogin.net user name admin password password
hi there can i run my router on wireless
When a bought my netgear router it did not come with direction or with a Cd of instructions . I was able to figure how to get it running . The problem is that people . People all around me can gain access to my connection. How can i put a password on my router to keep people from gain access to my connection.
its amazing i have had no issues with it yet i think its a very good system no drop outs at all and i run a lot on it as well thanks alot keep up the good work
my laptop is connected to my netgear n3000 wireless adsl2 but i forget the password and i need it for my phone how can i found out the password or change it please?
NEED HELP!!!! im trying to get internet in my new ipod touch, but cant seem to find my netgear password.(when i installed it i didnt set my own password) and now i dont know to do it.
I won’t a pass code
I recantly bought a netgear wireless n 900n doualband router that cost around
200 bucks because it`s about 100 ft. from my computer in which is a Sony Vio all in one pc. it is supposed to be the best money can buy.My old Linksys wireless G router was out of date and couldnt connect to the internet unless I possitioned the computer up against the closest wall in my home to the router and it was still week but some of the time it could connect. Does it have the strength to connect that far (100ft) the new ngw900n router a 5gh signal ability so how do I set up the ngw900n router to connect to my network?
Just wish to say your article is as astonishing. The clearness to your post is just spectacular and i can suppose you are a professional on this subject. Well together with your permission allow me to grasp your RSS feed to stay updated with approaching post. Thanks one million and please carry on the enjoyable work.
i need my password to login
i dont have abuisness iam retired i just want my lab top so i can walk around with it.
necesito ayuda para dejar con contraseña el router pra q no ocupen otras personas mi servicio de Internet el servicio router es excelente dinámico y fresco
como puedo hoctener una contrasena para que otras personas no usen mi servicio de internet
como puedo haser un nuevo password porque entre y presione reply de atra persona y ahora me pide un passworw para usar el router
forgot my password
need to set up a security block onmy internet
I CANT USE MY IPHONE4S ON THE WIFI. HOW DO I DISSCONNET THE WIFI PASSWORD OFF MY LAPTP?
i hav the cgd24g and both the mac address and serial #;s have worn spots and arent readable, how do i recover them?
pls help ! rplgrumpy@gmail.com
So, I’ve been trying to reset the password…and yes i already went to the routerlogin.net and it just takes me to support.netgear.com…I just really need to reset my password ): because I forgot it and I logged out of it D: and my Itouch is logged on it but I can’t figure out the password and I’ve even tried hacking it D:
I’ve read several excellent stuff here. Certainly price bookmarking for revisiting. I wonder how a lot attempt you set to create such a wonderful informative website.
After going into http://192.168.1.1/ and trying to put in my password and username, nothing happens! The pop up message just reappears again even though I’m sure I put the right username and password(because it was labeled under my router)!! Can any1 tell me why this keeps happening?
TL;DR put in username and password nothing happens.
Need for Login netgear54 mbps
WGR14v7 ein benutzername
Und Passwort/Kennword
Danke
i set up my wireless router and my xbox wont connect to the in ternet any suggestions on what to do
how i turn my netgear router private
hi can someone help me my router has blocked my password i cant conect my wifi to anything how do i unlock it
ok so my router wont work like when i try to take it around the house it wont let me! and i dont no how to fix it?
I have a netgear n300 wieless usb adapter and I keep gettng failed login on setting page, I used admin,and password
When I try using the 192.168.0.1 it tells me safari cant open the page. what does that mean?
I bought a tablet to replace laptop and don’t know the password for Netgear to get internet.
Netgear should provide more help.
как разблокировать беспроводной N300 ГИГАБИТНЫЙ МАРШРУТИЗАТОР WNR3500L
[…] Decoding the Web – Netgear router – 192.168.0.1 redirects … […]
[…] Decoding the Web – Netgear router – 192.168.0.1 redirects … […]
[…] Decoding the Web – Netgear router – 192.168.0.1 redirects … […]
[…] Netgear router – 192.168.0.1 redirects http://www.routerlogin. – fix . february 21, 2007 decoding. Click here Giveaway day – free licensed software daily. today, Android giveaway day. weather 5 days. […]
[…] Decoding the Web – Netgear router – 192.168.0.1 redirects … […]
[…] Netgear router – 192.168.0.1 redirects http://www.routerlogin. – fix . february 21, 2007 decoding. Click here Best buy: ultimate technology showroom, International retailer consumer electronics entertainment […]
[…] Netgear router – 192.168.0.1 redirects to … – 21.02.2007 · Netgear router – 192.168.0.1 redirects to http://www.routerlogin.com – how to fix it. February 21, 2007 by decoding… […]
[…] Netgear router – 192.168.0.1 redirects to … – 21.02.2007 · Netgear router – 192.168.0.1 redirects to http://www.routerlogin.com – how to fix it. February 21, 2007 by decoding… […]
[…] Netgear router – 192.168.0.1 redirects to www … – Feb 21, 2007 · Today I have installed my new Netgear router, and to be more specific it is the DG834PN model from the Wireless Rangemax series. It is a great product …… […]
[…] Netgear router – 192.168.0.1 redirects to www … – Feb 21, 2007 · Netgear router – 192.168.0.1 redirects to http://www.routerlogin.com – how to fix it. February 21, 2007 by decoding… […]
[…] Netgear router – 192.168.0.1 redirects to www … – 2007-02-21 · Netgear router – 192.168.0.1 redirects to http://www.routerlogin.com – how to fix it. February 21, 2007 by decoding… […]
[…] Netgear router – 192.168.0.1 redirects to www … – 2007-02-21 · Netgear router – 192.168.0.1 redirects to http://www.routerlogin.com – how to fix it. February 21, 2007 by decoding… […]
[…] Netgear router – 192.168.0.1 redirects to www … – 2007-02-21 · Netgear router – 192.168.0.1 redirects to http://www.routerlogin.com – how to fix it. February 21, 2007 by decoding… […]
[…] Netgear router – 192.168.0.1 redirects to www … – Feb 21, 2007 · Netgear router – 192.168.0.1 redirects to http://www.routerlogin.com – how to fix it. February 21, 2007 by decoding… […]
[…] Netgear router – 192.168.0.1 redirects to www … – Feb 21, 2007 · Netgear router – 192.168.0.1 redirects to http://www.routerlogin.com – how to fix it. February 21, 2007 by decoding… […]
netgear router wont accept my network key..says mismatch ..(paraphrase)help please
[…] specific it is the DG834PN model from the Wireless Rangemax series. It is a great product … Download Netgear router – 192.168.0.1 redirects to www … | […]
[…] Netgear router – 192.168.0.1 redirects to www … – Feb 21, 2007 · Today I have installed my new Netgear router, and to be more specific it is the DG834PN model from the Wireless Rangemax series. It is a great product …… […]
I have net gear WNR614 netgear. but every time after restarting the system it seems wifi is limited . I have to go to router setting and and have to set dns and ip adress again. how to set this one permenantly
I have been facing the same issue, I don’t know how to proceed further for it now, I always use direct ip page for it at 192.168.o.1 now.
ihave a netgear modem which internet works properly when i put my computer straight to the modem,but when i connect my wireless it internet does not work. i tried loggin into the modem using all factory links, but does not work. also when i go to the command prompt, the ip address in the default gateway has a mac address then the ip address 67.191.104.1 under it.. please assit
[…] issue of getting ‘Page cannot be displayed or is blank’ error. In this way, I solved 192.168.1.1 not working problem by troubleshooting the […]